Get your Medium Voltage Load Break Switches straight from the factory - 15kV Oil Immersed Four-Position LBS now available!

Medium Voltage Oil Immersed Four-Position 15kV Load Break Switches(LBS) Summarize Four-Position Oil Immersed Load Switch Anhuang Four-position Oil Immersed Load Switch can apply to the composite transformers with 50Hz AC and rated voltage of 12kV and 35kV. It is a nice and small load switch designed to meet the challenge of continually raising the load capacity of power net while the composite transformers usually have a very limited internal space. It uses the transformer oil as the media of insulation and that for preventing the electric arc. It uses a mechanical spring for reserving energy. Three phase linkage is available with it. Also it can promptly and accurately turn on or cut off the electric current. This switch can be applicable to any power distribution system with 12kV and 35kV and double power supply lines. Per customer request that load switch can be in any form for instance. It can be the buried type or one with the power operation mechanism. It can apply to all types of transformers. This switch is characteristic of T type, with four function positions and double power supply lines. The positions of double power supply line, power supply I, power supply II and turn off. The contact of the switch uses the double contact floating bridge flint, with very limited resistance. Meanwhile it generates great capacity of current passage. As a result, the electric power compensation is very good, greatly raising its anti-load disturbance performance. The static contact terminal board is fixed. This makes easier to install or build in the switch, hence making the operation more reliable. The newly added static contact assistant makes the contact between the static and dynamic contacts more accurate. This switch is installed on the side wall of the transformer’s oil tank. According to the requirement of power supply lines’ change or switching, please turn the load switch clockwise or anti clockwise with the special insulated function lever. For every single operation, make sure to turn the switch by 90 degree. In this way, we can repeat the process and turn it by 360 degree eventually. Main technical parameters FYN33 Type Four-Position Oil Immersed Load Switch figure-1

FYN33 Type Four-Position Oil Immersed Load Switch figure-1

Overall dimension FYN33 Type Four-Position Oil Immersed Load Switch figure-2

Reservation installation size for transformer housing FYN33 Type Four-Position Oil Immersed Load Switch figure-3

Installation 1) Before installation, check if the switching motion is flexible and accurate carefully, only after confirmed to be under good condition, the installation can be implemented, in addition, the load switch must be dried under 65±5℃condition by 24h. 2) Please take off the handle,pyramid-shaped spring,the limiting panel and the fastening bushed’ nuts from the load switch. Then makes the switch fastening bush and sealing ring go through the ready-made hole dia 34 in the transformer case,fasten the switch on the transformer’s case wthere the pre-welded nuts are available with 4 pieces nuts in M10x20. Also with the spring washer. Then tighten the fasten in bushing nuts. NOTICE: When tightening the M10 bolts, if the position hole is not identical and could not put in the bolt, please make sure to fix or correct the hole before installation. Otherwise the error installation will cause deformation of the install panel and it will possibly result in an operation accident of the load switch. Installation procedure 1636962661(1)

NOTICE: if found that the relative position of bolt hole deviates heavily when screw down the M10 bolts, you must amend the hole and then screw down it again. Otherwise, this will cause distortion to mounting plate, and may bring about malfunction to load switch. 1636962786(1)

5) After installation and connection, it is suggested to carry out “open” and “close” operation to check if the switch can be moved flexibly and if the position indication is correct, if any abnormal, please check the installation of switch and the connection of busbar according to article 2 and 4. Attention 1) This load switch can be used to open or close rated current only, while the application for closing and opening the failure current. If over rated current, forbidden to operate switch. 2) Only the special insulated operating arm can be used to operate this load switch to ensure personal safety. 3) For each operation, whenever the load switch is turned to a new position, the limiting panel must be adjusted first. Use the dedicated operation lever instead of the combined one to fix or hook the limiting panel and take it away from its original fix pin, turn for 90 degrees and then put it into the next fix pin. 4) Use the operation lever to hook of fix the handle of load switch,turn for 135 degree or so, then the spring’s energy reserving mechanism functions and the switches’ function position is changed to a new side. Hence,the handle will automatically return to 90 degree position.The switch can turn by 360 degree in this way in circulation,either clockwise or anti clockwise. Connection Diagram 1-2-T: Power 1 and Power 2 both linked with the transformer. 1-T: Power 1 linked with the transformer. 2-T: Power 2 linked with the transformer. 1-2: Power 1 linked with Power 2 while both of them are cut off from the transformer. 1636963396(1)